已经按照例程实现基本的功能，但是为什么串口转发的是前一个包

# Conflicts:
#	inc/board_config.h

CMakeLists.txt

@@ -4,10 +4,12 @@ include(cmake/toolchain.cmake)
 project(xlsw_3dp_LDC1612)
 
 set(VERSION_MAJOR 0)
-set(VERSION_MINOR 2)
-set(VERSION_PATCH 0)
+set(VERSION_MINOR F)
+set(VERSION_PATCH 1)
 set(VERSION "V${VERSION_MAJOR}.${VERSION_MINOR}.${VERSION_PATCH}")
 string(TIMESTAMP CURRENT_DATE "%Y-%m-%d")
+set(IIC_TYPE "AutoDetectDriveCurrent")
+#set(IIC_TYPE "HW-IIC")
 
 enable_language(C)
 enable_language(CXX)
@@ -30,6 +32,7 @@ set(TARGET_C_SRC
         ${CMAKE_SOURCE_DIR}/src/led.c
         ${CMAKE_SOURCE_DIR}/src/i2c.c
         ${CMAKE_SOURCE_DIR}/src/soft_i2c.c
+        ${CMAKE_SOURCE_DIR}/src/fwdgt.c
 )
 
 add_executable(xlsw_3dp_LDC1612 ${TARGET_C_SRC})

README.md

@@ -6,4 +6,148 @@
 
 ## 电涡流传感器模块通信协议
 
-通信协议：[LDC1612通信协议]{./CommunicationProtocol.md}
+通信协议：[LDC1612通信协议](CommunicationProtocol.md)
+
+---
+
+## LDC1612寄存器配置
+### **1. 软件复位 (RESET_DEV)**
+- **寄存器地址**: 0x1C
+- **写入值**: 0x8000
+- **字段解析**：
+    - **Bit 15 (RESET_DEV)**: 写1触发硬件复位，完成后自动清零。
+    - **Bits 14-0**: 保留位，必须写0。
+
+### **2. 进入休眠模式 (CONFIG)**
+- **寄存器地址**: 0x1A
+- **写入值**: 0x2801
+- **字段解析**（按位分解）：
+
+  | Bit位 | 字段名                | 值   | 功能说明                  |
+    |-------|-----------------------|-----|--------------------------|
+  | 15-14 | ACTIVE_CHAN           | 00  | 未使用（休眠模式下无效）     |
+  | 13    | SLEEP_MODE_EN         | 1   | 使能休眠模式               |
+  | 12    | RP_OVERRIDE_EN        | 0   | 禁用Rp覆盖（默认）          |
+  | 11    | SENSOR_ACTIVATE_SEL   | 0   | 全电流激活模式             |
+  | 10    | AUTO_AMP_DIS          | 0   | 启用自动幅度校正           |
+  | 9     | REF_CLK_SRC           | 0   | 使用内部时钟源             |
+  | 8     | Reserved              | 0   | 保留位                    |
+  | 7     | INTB_DIS              | 0   | 使能INTB中断              |
+  | 6     | HIGH_CURRENT_DRV      | 0   | 禁用高电流驱动模式         |
+  | 5-0   | Reserved              | 000001 | 保留位（默认值）          |
+
+### **3. 配置通道0时钟分频 (CLOCK_DIVIDERS_CH0)**
+- **寄存器地址**: 0x14
+- **写入值**: 0x1002
+- **字段解析**：
+
+  | 字段名             | 位域      | 值    | 功能说明                  |
+    |--------------------|-----------|-------|--------------------------|
+  | CH0_FIN_DIVIDER    | Bits 15-12 | 0x1   | 传感器分频系数=1（不分频） |
+  | Reserved           | Bits 11-10 | 0x0   | 保留位                   |
+  | CH0_FREF_DIVIDER   | Bits 9-0   | 0x002 | 参考分频系数=2，f_REF=40MHz/2=20MHz |
+
+### **4. 设置通道0转换时间 (RCOUNT_CH0)**
+- **寄存器地址**: 0x08
+- **写入值**: 0x04D6 (十进制1238)
+- **计算公式**：
+
+  \[
+  t_{C0} = \frac{(0x04D6 \times 16)}{20\text{MHz}} = 991\mu s
+  \]
+
+### **5. 设置通道0稳定时间 (SETTLECOUNT_CH0)**
+- **寄存器地址**: 0x10
+- **写入值**: 0x000A (十进制10)
+- **计算公式**：
+
+  \[
+  t_{S0} = \frac{(0x000A \times 16)}{20\text{MHz}} = 8\mu s
+  \]
+
+### **6. 配置通道0驱动电流 (DRIVE_CURRENT_CH0)**
+- **寄存器地址**: 0x1E
+- **写入值**: 0x9000
+- **字段解析**：
+
+  | 字段名             | 位域      | 值    | 功能说明                  |
+    |--------------------|-----------|-------|--------------------------|
+  | CH0_IDRIVE         | Bits 15-11 | 0x12  | 驱动电流值=18（对应Rp=6.6kΩ，查表9） |
+  | CH0_INIT_IDRIVE    | Bits 10-6  | 0x00  | 初始电流值（未使用）        |
+  | Reserved           | Bits 5-0   | 0x00  | 保留位                   |
+
+### **7. 多通道扫描配置 (MUX_CONFIG)**
+- **寄存器地址**: 0x1B
+- **写入值**: 0x820C
+- **字段解析**：
+
+  | 字段名             | 位域      | 值    | 功能说明                  |
+    |--------------------|-----------|-------|--------------------------|
+  | AUTOSCAN_EN        | Bit 15    | 1     | 启用自动扫描模式           |
+  | RR_SEQUENCE        | Bits 14-13 | 00   | 扫描顺序：Ch0→Ch1          |
+  | Reserved           | Bits 12-3 | 0x020 | 保留位（默认值）           |
+  | DEGLITCH           | Bits 2-0   | 0x4   | 去抖动滤波器带宽=3.3MHz    |
+
+### **8. 退出休眠并启动转换 (CONFIG)**
+- **寄存器地址**: 0x1A
+- **写入值**: 0x1601
+- **字段解析**（关键位）：
+
+  | Bit位 | 字段名                | 值   | 功能说明                  |
+    |-------|-----------------------|-----|--------------------------|
+  | 13    | SLEEP_MODE_EN         | 0   | 退出休眠模式              |
+  | 9     | REF_CLK_SRC           | 1   | 使用外部时钟（CLKIN=40MHz）|
+  | 12    | RP_OVERRIDE_EN        | 1   | 启用Rp覆盖（固定驱动电流） |
+
+### **关键参数总结表**
+| 寄存器名             | 地址  | 写入值 | 核心功能                     |
+|----------------------|-------|--------|----------------------------|
+| RESET_DEV            | 0x1C  | 0x8000 | 强制复位设备                 |
+| CONFIG (休眠)        | 0x1A  | 0x2801 | 进入配置模式                 |
+| CLOCK_DIVIDERS_CH0   | 0x14  | 0x1002 | 通道0时钟分频设置            |
+| RCOUNT_CH0           | 0x08  | 0x04D6 | 通道0转换时间=991μs          |
+| SETTLECOUNT_CH0      | 0x10  | 0x000A | 通道0稳定时间=8μs            |
+| DRIVE_CURRENT_CH0    | 0x1E  | 0x9000 | 通道0驱动电流=18（约1.5mA）  |
+| MUX_CONFIG           | 0x1B  | 0x820C | 启用双通道扫描（Ch0→Ch1）    |
+| CONFIG (启动)        | 0x1A  | 0x1601 | 退出休眠，启用外部时钟       |
+
+通过以上配置，设备将按以下流程运行：
+1. 复位后进入休眠模式，配置寄存器。
+2. 设置通道0的时钟分频、转换时间、稳定时间和驱动电流。
+3. 启用双通道自动扫描，设置去抖动滤波器。
+4. 退出休眠模式，开始连续转换。
+
+---
+
+## **自动校准配置（可选）**
+### **适用场景**
+- Rp未知或环境变化大时，通过自动校准获取初始电流值。
+
+### **操作流程**
+1. **设置目标至最大距离**
+2. **进入休眠模式**：
+   ```c
+   write_register(0x1A, 0x2801); // SLEEP_MODE_EN=1
+   ```
+3. **启用自动校准**：
+   ```c
+   // CLOCK_DIVIDERS_CH0配置分频
+   write_register(0x14, 0x1002); // FIN_DIV=1, FREF_DIV=2
+   // 禁用Rp覆盖
+   uint16_t config = read_register(0x1A);
+   config &= ~(1 << 12); // RP_OVERRIDE_EN=0
+   write_register(0x1A, config);
+   ```
+4. **启动测量并读取初始值**：
+   ```c
+   write_register(0x1A, 0x1601); // 退出休眠
+   delay(10); // 等待至少一次转换完成
+   uint16_t init_value = (read_register(0x1E) >> 6) & 0x1F; // 读取CH0_INIT_IDRIVE
+   ```
+5. **写入驱动电流**：
+   ```c
+   uint16_t drive_current = (init_value << 11) | 0x0000;
+   write_register(0x1E, drive_current);
+   ```
+   
+---

cmake/toolchain.cmake

@@ -41,12 +41,12 @@ function(print_size_of_target TARGET)
             )
 endfunction()
 
-function(_generate_file TARGET PREFIX VERSION DATE OUTPUT_EXTENSION OBJCOPY_BFD_OUTPUT)
+function(_generate_file TARGET PREFIX VERSION DATE IIC_TYPE OUTPUT_EXTENSION OBJCOPY_BFD_OUTPUT)
     get_target_property(TARGET_OUTPUT_NAME ${TARGET} OUTPUT_NAME)
     if (TARGET_OUTPUT_NAME)
-        set(OUTPUT_FILE_NAME "${PREFIX}_${VERSION}_${DATE}.${OUTPUT_EXTENSION}")
+        set(OUTPUT_FILE_NAME "${PREFIX}_${VERSION}_${DATE}_${IIC_TYPE}.${OUTPUT_EXTENSION}")
     else()
-        set(OUTPUT_FILE_NAME "${TARGET}_${VERSION}_${DATE}.${OUTPUT_EXTENSION}")
+        set(OUTPUT_FILE_NAME "${TARGET}_${VERSION}_${DATE}_${IIC_TYPE}.${OUTPUT_EXTENSION}")
     endif()
 
     get_target_property(RUNTIME_OUTPUT_DIRECTORY ${TARGET} RUNTIME_OUTPUT_DIRECTORY)
@@ -66,11 +66,11 @@ function(_generate_file TARGET PREFIX VERSION DATE OUTPUT_EXTENSION OBJCOPY_BFD_
 endfunction()
 
 function(generate_binary_file TARGET PREFIX)
-    _generate_file(${TARGET} "${PREFIX}" "${VERSION}" "${CURRENT_DATE}" "bin" "binary")
+    _generate_file(${TARGET} "${PREFIX}" "${VERSION}" "${CURRENT_DATE}" "${IIC_TYPE}" "bin" "binary")
 endfunction()
 
 function(generate_hex_file TARGET PREFIX)
-    _generate_file(${TARGET} "${PREFIX}" "${VERSION}" "${CURRENT_DATE}" "hex" "ihex")
+    _generate_file(${TARGET} "${PREFIX}" "${VERSION}" "${CURRENT_DATE}" "${IIC_TYPE}" "hex" "ihex")
 endfunction()
 
 set(CMAKE_EXECUTABLE_SUFFIX_C   .elf)

inc/board_config.h

@@ -5,13 +5,16 @@
 #ifndef BOARD_CONFIG_H
 #define BOARD_CONFIG_H
 
-#define SOFTWARE_IIC
+// #define SOFTWARE_IIC
 
 // #define DEBUG_VERBOES
 
+// #define RS485_MAX13487
+
+// #define DEBUG_VOFA_TOOL
+
 /******************************************************************************/
 
-#define I2C_SPEED       20000
 #define RCU_GPIO_I2C         RCU_GPIOF
 #define RCU_I2C              RCU_I2C0
 #define I2C_SCL_PORT         GPIOF
@@ -33,4 +36,13 @@
 
 /******************************************************************************/
 
+#define LED_PORT             GPIOA
+#define LED_PIN              GPIO_PIN_7
+#define LED_RCU              RCU_GPIOA
+#define LED_BLINK_TIMER_RCU  RCU_TIMER16
+#define LED_BLINK_TIMER      TIMER16
+#define LED_BLINK_IRQ        TIMER16_IRQn
+
+/******************************************************************************/
+
 #endif //BOARD_CONFIG_H

inc/fwdgt.h

@@ -0,0 +1,15 @@
+//
+// Created by yelv1 on 24-12-29.
+//
+
+#ifndef FWDGT_H
+#define FWDGT_H
+
+#include "gd32e23x.h"
+#include "board_config.h"
+
+void watchdog_init(void);
+
+void fwdgt_reset_mcu(void);
+
+#endif //FWDGT_H

inc/i2c.h

@@ -19,13 +19,7 @@
 
 /******************************************************************************/
 
-#define I2C_SCL_HIGH()      gpio_bit_set(I2C_SCL_PORT, I2C_SCL_PIN)
-#define I2C_SCL_LOW()       gpio_bit_reset(I2C_SCL_PORT, I2C_SCL_PIN)
-#define I2C_SDA_HIGH()      gpio_bit_set(I2C_SDA_PORT, I2C_SDA_PIN)
-#define I2C_SDA_LOW()       gpio_bit_reset(I2C_SDA_PORT, I2C_SDA_PIN)
-#define I2C_SDA_READ()      gpio_input_bit_get(I2C_SDA_PORT, I2C_SDA_PIN)
-
-/******************************************************************************/
+#define I2C_SPEED       100*(1000)
 
 #define I2C_TIME_OUT    (uint16_t)(5000)
 #define I2C_OK          1

inc/ldc1612.h

@@ -51,16 +51,18 @@
 #define LDC1612_DRIVE_CURRENT              0x9000  //A000
 #define LDC1612_MUX_CONFIG                 0x020C  // no auto scan and filter bandwidth 3.3MHz
 #define LDC1612_SENSOR_CONFIG              0x1601
+#define LDC1612_SLEEP_MODE                 0x2801
 #define LDC1612_ERROR_CONFIG               0x0000
 #define LC_STABILIZE_TIME_CH0              0x001E //30
 #define LDC1612_RESET_DEV                  0x8000 //[15:0] 0b1000 0000 0000 0000
 
 /******************************************************************************/
 
-#define COIL_RP_KOM              15.727
+#define COIL_RP_KOM              7.2
 #define COIL_L_UH                33
 #define COIL_C_PF                150
 #define COIL_Q_FACTOR            35.97
+#define COIL_FREQ_HZ             2262000
 
 /******************************************************************************/
 
@@ -94,4 +96,6 @@ uint32_t ldc1612_get_raw_channel_result(uint8_t channel);
 
 uint32_t ldc1612_parse_raw_result(uint32_t raw_result);
 
+void ldc1612_drvie_current_detect(uint8_t channel);
+
 #endif //LDC1612_H

inc/led.h

@@ -6,24 +6,7 @@
 #define LED_H
 
 #include "gd32e23x_it.h"
-#include "gd32e23x.h"
-#include "systick.h"
-#include <stdbool.h>
-#include <string.h>
-#include <stdio.h>
-#include <stdlib.h>
-#include <math.h>
-
-/******************************************************************************/
-
-#define LED_PORT            GPIOA
-#define LED_PIN             GPIO_PIN_7
-#define LED_RCU             RCU_GPIOA
-#define LED_TIMER_RCU       RCU_TIMER16
-#define LED_TIMER           TIMER16
-#define LED_IRQ             TIMER16_IRQn
-
-/******************************************************************************/
+#include "board_config.h"
 
 void led_config(void);
 

inc/main.h

@@ -35,10 +35,21 @@ OF SUCH DAMAGE.
 #ifndef MAIN_H
 #define MAIN_H
 
-// #define DEBUG_VERBOES
+#include <stdio.h>
+#include <stdbool.h>
+#include "gd32e23x.h"
+#include "systick.h"
+#include "gd32e23x_libopt.h"
+#include "rs485.h"
+#include "led.h"
+#include "ldc1612.h"
+#include "fwdgt.h"
+#include "board_config.h"
 
-void watchdog_init(void);
-
-void reset_mcu(void);
+#ifdef SOFTWARE_IIC
+#include "soft_i2c.h"
+#else
+#include "i2c.h"
+#endif
 
 #endif /* MAIN_H */

inc/rs485.h

@@ -8,33 +8,21 @@
 #include "gd32e23x_it.h"
 #include "gd32e23x.h"
 #include "systick.h"
-#include <stdbool.h>
-#include <string.h>
 #include <stdio.h>
-#include <stdlib.h>
-#include <sys/types.h>
-#include "i2c.h"
+#include <string.h>
+#include <stdbool.h>
 #include "ldc1612.h"
 #include "tmp112.h"
-
-/******************************************************************************/
-
-#define RS485_RCU            RCU_USART0
-#define RS485_GPIO_RCU       RCU_GPIOA
-#define RS485_GPIO_PORT      GPIOA
-#define RS485_TX_PIN         GPIO_PIN_2
-#define RS485_RX_PIN         GPIO_PIN_3
-#define RS485_PHY            USART0
-#define RS485_BAUDRATE       115200U
-#define RS485_EN_PIN         GPIO_PIN_1
+#include "fwdgt.h"
+#include "board_config.h"
 
 /******************************************************************************/
 
 #define RX_BUFFER_SIZE            32
 
-#define LDC1612_PACKAGE_HEADER   0xD5
-#define LDC1612_BOARD_TYPE       0x03
-#define LDC1612_PACKAGE_LENGTH   0x02
+#define PROTOCOL_PACKAGE_HEADER   0xD5
+#define PROTOCOL_BOARD_TYPE       0x03
+#define PROTOCOL_PACKAGE_LENGTH   0x02
 
 /******************************************************************************/
 
@@ -49,14 +37,28 @@ typedef enum
 
 /******************************************************************************/
 
+uint8_t Command_Write(uint8_t *data, uint8_t length);
+
+uint8_t Command_GetCommand(uint8_t *command);
+
+/******************************************************************************/
+
 void rs485_config(void);
+
 void process_command(uint8_t* cmd, size_t length);
+
 uint8_t calculate_crc(uint8_t data[], uint8_t data_length);
+
 validation_result_t validate_package_crc(uint8_t* data, uint8_t data_length);
+
 validation_result_t validate_package_header(uint8_t* data);
+
 validation_result_t validate_package_type(uint8_t* data);
+
 validation_result_t validate_data_length(uint8_t* data);
+
 void eddy_current_value_report(void);
+
 void tempture_value_report(void);
 
 #endif //RS485_H

inc/tmp112.h

@@ -7,12 +7,6 @@
 
 #include "gd32e23x_it.h"
 #include "gd32e23x.h"
-#include "systick.h"
-#include <stdbool.h>
-#include <string.h>
-#include <stdio.h>
-#include <stdlib.h>
-#include <math.h>
 
 #include "board_config.h"
 
@@ -28,6 +22,8 @@
 
 /******************************************************************************/
 
+#define TMP112A_TEMP_REG     0x00
+
 uint32_t tmp112a_get_raw_channel_result(void);
 
 #endif //TMP112_H

src/fwdgt.c

@@ -0,0 +1,28 @@
+//
+// Created by yelv1 on 24-12-29.
+//
+
+#include "fwdgt.h"
+
+void watchdog_init(void) {
+    /* Enable the LSI clock */
+    rcu_osci_on(RCU_IRC40K);
+    rcu_osci_stab_wait(RCU_IRC40K);
+
+    /* Configure FWDGT counter clock: 40KHz(IRC40K) / 64 = 0.625 KHz */
+    fwdgt_config(625, FWDGT_PSC_DIV64); // Set timeout to 1 seconds (625 / 0.625 KHz)
+
+    /* Enable FWDGT */
+    fwdgt_enable();
+}
+
+void fwdgt_reset_mcu(void) {
+    /* Enable the write access to the FWDGT_CTL register */
+    FWDGT_CTL = FWDGT_WRITEACCESS_ENABLE;
+
+    /* Configure FWDGT to trigger a system reset */
+    fwdgt_config(50, FWDGT_PSC_DIV4);
+
+    /* Reload the counter to trigger the reset */
+    fwdgt_counter_reload();
+}

src/gd32e23x_it.c

@@ -39,6 +39,8 @@ OF SUCH DAMAGE.
 #include "rs485.h"
 #include "led.h"
 
+extern uint8_t readBuffer[16];
+
 /*!
     \brief      this function handles NMI exception
     \param[in]  none
@@ -103,15 +105,15 @@ void SysTick_Handler(void) {
   * @retval None
   */
 void TIMER16_IRQHandler(void) {
-    if (timer_interrupt_flag_get(LED_TIMER, TIMER_INT_FLAG_UP) == SET) {
-        timer_interrupt_flag_clear(LED_TIMER, TIMER_INT_FLAG_UP);
+    if (timer_interrupt_flag_get(LED_BLINK_TIMER, TIMER_INT_FLAG_UP) == SET) {
+        timer_interrupt_flag_clear(LED_BLINK_TIMER, TIMER_INT_FLAG_UP);
         static uint8_t led_status = 0;
         if (led_status) {
             gpio_bit_write(LED_PORT, LED_PIN, RESET);
-            timer_autoreload_value_config(LED_TIMER, 19200);
+            timer_autoreload_value_config(LED_BLINK_TIMER, 19200);
         } else {
             gpio_bit_write(LED_PORT, LED_PIN, SET);
-            timer_autoreload_value_config(LED_TIMER, 800);
+            timer_autoreload_value_config(LED_BLINK_TIMER, 800);
         }
         led_status = !led_status;
     }
@@ -119,22 +121,21 @@ void TIMER16_IRQHandler(void) {
 
 void USART0_IRQHandler(void) {
     static uint8_t rx_index = 0;
-    static uint8_t rx_buffer[RX_BUFFER_SIZE];
 
     if (RESET != usart_interrupt_flag_get(USART0, USART_INT_FLAG_RBNE)) {
-        usart_interrupt_flag_clear(USART0, USART_INT_FLAG_RBNE);
-        uint8_t received_data = (uint8_t) usart_data_receive(USART0);
+        // usart_interrupt_flag_clear(USART0, USART_INT_FLAG_RBNE);
+        // uint8_t received_data = (uint8_t) usart_data_receive(USART0);
 
         // 将接收到的数据存储到缓冲区
-        if (rx_index < RX_BUFFER_SIZE - 1) {
-            rx_buffer[rx_index++] = received_data;
+        if (rx_index < sizeof(readBuffer) - 1) {
+            readBuffer[rx_index++] = usart_data_receive(USART0);
         }
     }
 
     if (RESET != usart_interrupt_flag_get(USART0, USART_INT_FLAG_IDLE)) {
         usart_interrupt_flag_clear(USART0, USART_INT_FLAG_IDLE);
 
-        process_command(rx_buffer, rx_index); // 处理指令
+        Command_Write(readBuffer, rx_index);// 处理指令
 
         rx_index = 0; // 重置缓冲区索引
         return;

src/ldc1612.c

@@ -276,3 +276,20 @@ uint32_t ldc1612_parse_raw_result(uint32_t raw_result) {
 
     return raw_result;
 }
+
+void ldc1612_drvie_current_detect(uint8_t channel) {
+    uint8_t data[2] = {0};
+    uint16_t init_value = 0 , drive_current = 0;
+
+    ldc1612_set_sensor_config(LDC1612_SLEEP_MODE);
+    ldc1612_set_freq_divide(channel);
+    soft_i2c_read_16bits(LDC1612_ADDR, SENSOR_CONFIG_REG, data);
+    ldc1612_set_sensor_config(LDC1612_SLEEP_MODE);
+    ldc1612_set_sensor_config(LDC1612_SENSOR_CONFIG); //0x1A --0x1601
+    delay_ms(10);
+    soft_i2c_read_16bits(LDC1612_ADDR, SET_DRIVER_CURRENT_REG, data);
+
+    init_value = (((data[0] << 8) | data[1]) >> 6) & 0x1F;
+    drive_current = (init_value << 11) | 0x0000;
+    printf("init value: 0x%x\tdrive current: 0x%x\n", init_value, drive_current);
+}

src/led.c

@@ -11,8 +11,8 @@ void led_config(void) {
     gpio_output_options_set(LED_PORT, GPIO_OTYPE_PP, GPIO_OSPEED_50MHZ, LED_PIN);
     gpio_bit_write(LED_PORT, LED_PIN, SET);
 
-    rcu_periph_clock_enable(LED_TIMER_RCU);
-    timer_deinit(LED_TIMER);
+    rcu_periph_clock_enable(LED_BLINK_TIMER_RCU);
+    timer_deinit(LED_BLINK_TIMER);
 
     timer_parameter_struct timer_initpara;
     timer_struct_para_init(&timer_initpara);
@@ -21,12 +21,12 @@ void led_config(void) {
     timer_initpara.counterdirection = TIMER_COUNTER_UP;
     timer_initpara.period = 9999;
     timer_initpara.clockdivision = TIMER_CKDIV_DIV1;
-    timer_init(LED_TIMER, &timer_initpara);
+    timer_init(LED_BLINK_TIMER, &timer_initpara);
 
-    timer_auto_reload_shadow_enable(LED_TIMER);
-    timer_interrupt_enable(LED_TIMER, TIMER_INT_UP);
+    timer_auto_reload_shadow_enable(LED_BLINK_TIMER);
+    timer_interrupt_enable(LED_BLINK_TIMER, TIMER_INT_UP);
 
-    timer_enable(LED_TIMER);
+    timer_enable(LED_BLINK_TIMER);
 
-    nvic_irq_enable(LED_IRQ, 2);
+    nvic_irq_enable(LED_BLINK_IRQ, 3U);
 }

src/main.c

@@ -5,44 +5,10 @@
     \version 2024-02-22, V2.1.0, firmware for GD32E23x
 */
 #include "main.h"
-#include <stdio.h>
-#include "gd32e23x.h"
-#include "systick.h"
-#include "gd32e23x_libopt.h"
-#include "rs485.h"
-#include "led.h"
-#include "i2c.h"
-#include "ldc1612.h"
-#include "board_config.h"
 
-#ifdef SOFTWARE_IIC
-#include "soft_i2c.h"
-#else
-#include "i2c.h"
-#endif
+bool g_statusSwitch = false;
 
-void watchdog_init(void) {
-    /* Enable the LSI clock */
-    rcu_osci_on(RCU_IRC40K);
-    rcu_osci_stab_wait(RCU_IRC40K);
-
-    /* Configure FWDGT counter clock: 40KHz(IRC40K) / 64 = 0.625 KHz */
-    fwdgt_config(625, FWDGT_PSC_DIV64); // Set timeout to 1 seconds (625 / 0.625 KHz)
-
-    /* Enable FWDGT */
-    fwdgt_enable();
-}
-
-void reset_mcu(void) {
-    /* Enable the write access to the FWDGT_CTL register */
-    FWDGT_CTL = FWDGT_WRITEACCESS_ENABLE;
-
-    /* Configure FWDGT to trigger a system reset */
-    fwdgt_config(50, FWDGT_PSC_DIV4);
-
-    /* Reload the counter to trigger the reset */
-    fwdgt_counter_reload();
-}
+uint8_t readBuffer[16];
 
 /*!
     \brief      main function
@@ -76,9 +42,23 @@ int main(void) {
     /* Initialize watchdog */
     watchdog_init();
 
+    uint8_t command[10];
+    uint8_t command_length = 0;
+
     while (1) {
-        delay_ms(99);
+
+        // delay_ms(10);
         fwdgt_counter_reload();
+        command_length = Command_GetCommand(command);
+        if (command_length != 0)
+        {
+            for (int i = 0; i < command_length; i++)
+            {
+                printf("%c", command[i]);
+            }
+        }
+        // if (g_statusSwitch)
+        // {eddy_current_value_report();}
     }
 }
 

src/rs485.c

@@ -7,7 +7,46 @@
 uint8_t package_header[3] = {0xB5, 0xF0, 0x04};
 uint8_t package_data[4] = {0};
 
+extern bool g_statusSwitch;
+
 void rs485_config(void) {
+#ifndef RS485_MAX13487
+    rcu_periph_clock_enable(RS485_GPIO_RCU);
+    rcu_periph_clock_enable(RS485_RCU);
+
+    gpio_af_set(RS485_GPIO_PORT, GPIO_AF_1, RS485_TX_PIN | RS485_RX_PIN | RS485_EN_PIN);
+
+    /* configure USART Tx&Rx as alternate function push-pull */
+    gpio_mode_set(RS485_GPIO_PORT, GPIO_MODE_AF, GPIO_PUPD_PULLUP, RS485_TX_PIN | RS485_RX_PIN);
+    gpio_output_options_set(RS485_GPIO_PORT, GPIO_OTYPE_PP, GPIO_OSPEED_10MHZ, RS485_TX_PIN | RS485_RX_PIN);
+
+    /* configure RS485 EN Pin */
+    gpio_mode_set(RS485_GPIO_PORT, GPIO_MODE_AF, GPIO_PUPD_NONE, RS485_EN_PIN);
+    gpio_output_options_set(RS485_GPIO_PORT, GPIO_OTYPE_PP, GPIO_OSPEED_50MHZ, RS485_EN_PIN);
+    // gpio_bit_write(RS485_GPIO_PORT, RS485_EN_PIN, SET);
+
+    /* USART configure */
+    usart_deinit(RS485_PHY);
+    usart_baudrate_set(RS485_PHY, RS485_BAUDRATE);
+    // usart_parity_config(RS485_PHY, USART_PM_NONE);
+    // usart_word_length_set(RS485_PHY, USART_WL_8BIT);
+    // usart_stop_bit_set(RS485_PHY, USART_STB_1BIT);
+    usart_receive_config(RS485_PHY, USART_RECEIVE_ENABLE);
+    usart_transmit_config(RS485_PHY, USART_TRANSMIT_ENABLE);
+
+    usart_driver_assertime_config(RS485_PHY, 0x01);
+    usart_driver_deassertime_config(RS485_PHY, 0x01);
+
+    // usart_depolarity_config(USART0, USART_DEP_HIGH);
+    // usart_depolarity_config(USART0, USART_DEP_LOW);
+
+    usart_rs485_driver_enable(RS485_PHY);
+    usart_enable(RS485_PHY);
+
+    nvic_irq_enable(USART0_IRQn, 0);
+    usart_interrupt_enable(RS485_PHY, USART_INT_RBNE);
+    usart_interrupt_enable(RS485_PHY, USART_INT_IDLE);
+#else
     rcu_periph_clock_enable(RS485_GPIO_RCU);
     rcu_periph_clock_enable(RS485_RCU);
 
@@ -33,6 +72,7 @@ void rs485_config(void) {
     nvic_irq_enable(USART0_IRQn, 0);
     usart_interrupt_enable(RS485_PHY, USART_INT_RBNE);
     usart_interrupt_enable(RS485_PHY, USART_INT_IDLE);
+#endif
 }
 
 void process_command(uint8_t *cmd, size_t length) {
@@ -49,14 +89,12 @@ void process_command(uint8_t *cmd, size_t length) {
             // printf("%d", length);
             sprintf(combined_str, "%c%c", cmd[3], cmd[4]);
             if (strcmp(combined_str, "M1") == 0) {
-                eddy_current_value_report();
-            } else if (strcmp(combined_str, "M2") == 0)
-            {
-                tempture_value_report();
-            } else if (strcmp(combined_str, "M3") == 0)
-            {
-                printf("%c%c%c%c%c%c", 0xB5, 0xF1, 0x02, 0x6F, 0x6B, 0xCC);
-                reset_mcu();
+                g_statusSwitch = true;
+            } else if (strcmp(combined_str, "M2") == 0) {
+                g_statusSwitch = false;
+            } else if (strcmp(combined_str, "M3") == 0) {
+                printf("%c%c%c%c%c%c", 0xB5, 0xF0, 0x02, 0x6F, 0x6B, 0xCC);
+                fwdgt_reset_mcu();
             } else {
                 printf("%c%c%c%c%c%c%c", 0xB5, 0xF0, 0x03, 0x65, 0x72, 0x72, 0x3C);
                 return;
@@ -98,7 +136,7 @@ validation_result_t validate_package_crc(uint8_t *data, uint8_t data_length) {
 }
 
 validation_result_t validate_package_header(uint8_t *data) {
-    if (data[0] == LDC1612_PACKAGE_HEADER) {
+    if (data[0] == PROTOCOL_PACKAGE_HEADER) {
         return VALIDATION_SUCCESS;
     } else {
         return VALIDATION_HEADER_ERROR;
@@ -106,7 +144,7 @@ validation_result_t validate_package_header(uint8_t *data) {
 }
 
 validation_result_t validate_package_type(uint8_t *data) {
-    if (data[1] == LDC1612_BOARD_TYPE) {
+    if (data[1] == PROTOCOL_BOARD_TYPE) {
         return VALIDATION_SUCCESS;
     } else {
         return VALIDATION_TYPE_ERROR;
@@ -114,7 +152,7 @@ validation_result_t validate_package_type(uint8_t *data) {
 }
 
 validation_result_t validate_data_length(uint8_t *data) {
-    if (data[2] == LDC1612_PACKAGE_LENGTH) {
+    if (data[2] == PROTOCOL_PACKAGE_LENGTH) {
         return VALIDATION_SUCCESS;
     } else {
         return VALIDATION_LENGTH_ERROR;
@@ -131,6 +169,15 @@ void eddy_current_value_report(void) {
     package_data[2] = (eddy_current_value_uint32 >> 8) & 0xFF;
     package_data[3] = eddy_current_value_uint32 & 0xFF;
 
+
+#ifdef DEBUG_VOFA_TOOL
+    printf("%d\n", eddy_current_value_uint32);
+#else
+    package_data[0] = (eddy_current_value_uint32 >> 24) & 0xFF;
+    package_data[1] = (eddy_current_value_uint32 >> 16) & 0xFF;
+    package_data[2] = (eddy_current_value_uint32 >> 8) & 0xFF;
+    package_data[3] = eddy_current_value_uint32 & 0xFF;
+
     uint8_t combined_data[7];
     memcpy(combined_data, package_header, 3);
     memcpy(combined_data + 3, package_data, 4);
@@ -138,6 +185,7 @@ void eddy_current_value_report(void) {
     printf("%c%c%c", package_header[0], package_header[1], package_header[2]);
     printf("%c%c%c%c", package_data[0], package_data[1], package_data[2], package_data[3]);
     printf("%c", calculate_crc(combined_data, 8));
+#endif
 }
 
 void tempture_value_report(void) {

src/soft_i2c.c

@@ -13,7 +13,7 @@
 void soft_i2c_delay(void) {
     delay_us(20); // Adjust delay as needed
     /* delay to freq
-     *  20KHz: delay_us(20);
+     *  15KHz: delay_us(20);
      *  65KHz: delay_us(1);
      */
 }
@@ -44,15 +44,12 @@ void soft_i2c_config(void) {
     \retval     none
 */
 void soft_i2c_start(void) {
-    // sda_out();
     I2C_SDA_HIGH();
     I2C_SCL_HIGH();
     soft_i2c_delay();
     I2C_SDA_LOW();
     soft_i2c_delay();
     I2C_SCL_LOW();
-    // soft_i2c_delay();
-    // 从全高开始，SCL为高期间，SDA下降沿表示start信号，再拉低SCL
 }
 
 /*!
@@ -69,7 +66,6 @@ void soft_i2c_stop(void) {
     I2C_SCL_HIGH();
     soft_i2c_delay();
     I2C_SDA_HIGH();
-    // 从全低开始，SCL为高期间，SDA上升沿表示stop
 }
 
 /*!
@@ -87,7 +83,6 @@ void soft_i2c_send_ack(void) {
     I2C_SCL_LOW();
     soft_i2c_delay();
     I2C_SDA_HIGH();
-    // SCL产生一个正常的时钟周期，其间SDA始终为低电平，表示ACK
 }
 
 /*!
@@ -97,7 +92,6 @@ void soft_i2c_send_ack(void) {
     \retval     none
 */
 void soft_i2c_send_nack(void) {
-    // sda_out();
     I2C_SDA_HIGH();
     soft_i2c_delay();
     I2C_SCL_HIGH();
@@ -105,7 +99,6 @@ void soft_i2c_send_nack(void) {
     I2C_SCL_LOW();
     soft_i2c_delay();
     I2C_SDA_HIGH();
-    // SCL产生一个正常的时钟周期，其间SDA始终为高电平，表示NACK
 }
 
 /*!
@@ -115,13 +108,11 @@ void soft_i2c_send_nack(void) {
     \retval     0: ACK received, 1: ACK not received
 */
 uint8_t soft_i2c_wait_ack(void) {
-    // sda_in();
     I2C_SDA_HIGH();
     soft_i2c_delay();
     I2C_SCL_HIGH();
     soft_i2c_delay();
     uint8_t ack = !I2C_SDA_READ();
-    //ACK信号是第九个时钟期间，SDA被从机在SCL高期间，拉低并保持低电平。此处判断SDA是否被拉低，被拉低则返回0，取反为1，表示收到ACK
     I2C_SCL_LOW();
     return ack;
 }
@@ -135,19 +126,18 @@ uint8_t soft_i2c_wait_ack(void) {
 void soft_i2c_send_byte(uint8_t byte) {
     // sda_out();
     for (int i = 0; i < 8; i++) {
-        if (byte & 0x80) { //通过&操作获取第一位是1还是0
-            I2C_SDA_HIGH(); //SCL低电平期间，SDA高电平表示1
+        if (byte & 0x80) {
+            I2C_SDA_HIGH();
         } else {
-            I2C_SDA_LOW(); //SCL低电平期间，SDA低电平表示0
+            I2C_SDA_LOW();
         }
-        byte <<= 1; //左移一位，把原本第二位的数据移到第一位，再判断高低电平
+        byte <<= 1;
         soft_i2c_delay();
-        I2C_SCL_HIGH(); //SCL拉高电平，SDA电平状态保持不变
+        I2C_SCL_HIGH();
+        soft_i2c_delay();
+        I2C_SCL_LOW();
         soft_i2c_delay();
-        I2C_SCL_LOW(); //SCL拉低电平
-        delay_us(5);
     }
-    // i2c_wait_ack();
 }
 
 /*!
@@ -157,9 +147,8 @@ void soft_i2c_send_byte(uint8_t byte) {
     \retval     received byte
 */
 uint8_t soft_i2c_receive_byte(uint8_t ack) {
-    // sda_in();
     uint8_t byte = 0;
-    I2C_SDA_HIGH(); //从高开始
+    I2C_SDA_HIGH();
     for (int i = 0; i < 8; i++) {
         byte <<= 1;
         I2C_SCL_HIGH();

src/tmp112.c

@@ -11,9 +11,9 @@ uint32_t tmp112a_get_raw_channel_result(void) {
     // ldc1612_iic_read_16bits(CONVERTION_RESULT_REG_START + channel, value);
 
 #ifdef SOFTWARE_IIC
-    soft_i2c_read_16bits(TMP112A_ADDR, 0x00, value);
+    soft_i2c_read_16bits(TMP112A_ADDR, TMP112A_TEMP_REG, value);
 #else
-    i2c_read_16bits(TMP112A_ADDR, 0x00, value);
+    i2c_read_16bits(TMP112A_ADDR, TMP112A_TEMP_REG, value);
 #endif
 
     raw_value = ((uint16_t) (value[0] << 4) | (value[1]>>4));