generated from hulk/gd32e23x_template_cmake_vscode
108 lines
4.0 KiB
C
108 lines
4.0 KiB
C
#include "uart.h"
|
||
#include "gd32e23x_usart.h"
|
||
#include "gd32e23x_rcu.h"
|
||
#include "gd32e23x_gpio.h"
|
||
#include "board_config.h"
|
||
#include "uart_ring_buffer.h"
|
||
|
||
|
||
void rs485_init(void) {
|
||
|
||
#ifndef RS485_MAX13487
|
||
/* 使能 GPIOA 和 USART0 时钟 */
|
||
rcu_periph_clock_enable(RS485_GPIO_RCU);
|
||
rcu_periph_clock_enable(RS485_RCU);
|
||
|
||
/* 配置 PA2 为 USART0_TX，PA3 为 USART0_RX */
|
||
gpio_af_set(RS485_GPIO_PORT, GPIO_AF_1, RS485_TX_PIN | RS485_RX_PIN | RS485_EN_PIN);
|
||
|
||
gpio_mode_set(RS485_GPIO_PORT, GPIO_MODE_AF, GPIO_PUPD_PULLUP, RS485_TX_PIN | RS485_RX_PIN);
|
||
gpio_output_options_set(RS485_GPIO_PORT, GPIO_OTYPE_PP, GPIO_OSPEED_50MHZ, RS485_TX_PIN | RS485_RX_PIN);
|
||
|
||
gpio_mode_set(RS485_GPIO_PORT, GPIO_MODE_AF, GPIO_PUPD_NONE, RS485_EN_PIN);
|
||
gpio_output_options_set(RS485_GPIO_PORT, GPIO_OTYPE_PP, GPIO_OSPEED_50MHZ, RS485_EN_PIN);
|
||
|
||
/* 配置波特率、数据位、停止位等 */
|
||
usart_deinit(RS485_PHY);
|
||
usart_word_length_set(RS485_PHY, USART_WL_8BIT);
|
||
usart_stop_bit_set(RS485_PHY, USART_STB_1BIT);
|
||
usart_parity_config(RS485_PHY, USART_PM_NONE);
|
||
usart_baudrate_set(RS485_PHY, RS485_BAUDRATE);
|
||
usart_receive_config(RS485_PHY, USART_RECEIVE_ENABLE);
|
||
usart_transmit_config(RS485_PHY, USART_TRANSMIT_ENABLE);
|
||
|
||
usart_driver_assertime_config(RS485_PHY, 0x01);
|
||
usart_driver_deassertime_config(RS485_PHY, 0x10);
|
||
|
||
usart_rs485_driver_enable(RS485_PHY);
|
||
|
||
usart_enable(RS485_PHY);
|
||
|
||
nvic_irq_enable(RS485_IRQ, 0);
|
||
usart_interrupt_enable(RS485_PHY, USART_INT_RBNE);
|
||
// usart_interrupt_enable(RS485_PHY, USART_INT_IDLE);
|
||
|
||
#else
|
||
rcu_periph_clock_enable(RS485_GPIO_RCU);
|
||
rcu_periph_clock_enable(RS485_RCU);
|
||
|
||
gpio_af_set(RS485_GPIO_PORT, GPIO_AF_1, GPIO_PIN_2 | GPIO_PIN_3);
|
||
|
||
/* configure USART Tx&Rx as alternate function push-pull */
|
||
gpio_mode_set(RS485_GPIO_PORT, GPIO_MODE_AF, GPIO_PUPD_PULLUP, RS485_TX_PIN | RS485_RX_PIN);
|
||
gpio_output_options_set(RS485_GPIO_PORT, GPIO_OTYPE_PP, GPIO_OSPEED_10MHZ, RS485_TX_PIN | RS485_RX_PIN);
|
||
|
||
/* configure RS485 EN Pin */
|
||
gpio_mode_set(RS485_GPIO_PORT, GPIO_MODE_OUTPUT, GPIO_PUPD_NONE, RS485_EN_PIN);
|
||
gpio_output_options_set(RS485_GPIO_PORT, GPIO_OTYPE_PP, GPIO_OSPEED_50MHZ, RS485_EN_PIN);
|
||
gpio_bit_write(RS485_GPIO_PORT, RS485_EN_PIN, SET);
|
||
|
||
/* USART configure */
|
||
usart_deinit(RS485_PHY);
|
||
usart_baudrate_set(RS485_PHY, RS485_BAUDRATE);
|
||
usart_receive_config(RS485_PHY, USART_RECEIVE_ENABLE);
|
||
usart_transmit_config(RS485_PHY, USART_TRANSMIT_ENABLE);
|
||
|
||
usart_enable(RS485_PHY);
|
||
|
||
nvic_irq_enable(USART0_IRQn, 0);
|
||
usart_interrupt_enable(RS485_PHY, USART_INT_RBNE);
|
||
usart_interrupt_enable(RS485_PHY, USART_INT_IDLE);
|
||
|
||
#endif // RS485_MAX13487
|
||
}
|
||
|
||
/******************************************************************************/
|
||
/* 具体的中断处理函数实现 */
|
||
/******************************************************************************/
|
||
|
||
void usart0_irq_handler(void) {
|
||
// 处理USART0的接收中断
|
||
if(usart_interrupt_flag_get(USART0, USART_INT_FLAG_RBNE)) {
|
||
uint8_t data = usart_data_receive(USART0);
|
||
// 使用原有的环形缓冲区处理逻辑
|
||
(void)uart_ring_buffer_put(data); // 缓冲满时丢弃，返回值可用于统计
|
||
}
|
||
|
||
// 处理USART0的空闲中断
|
||
if(usart_interrupt_flag_get(USART0, USART_INT_FLAG_IDLE)) {
|
||
usart_interrupt_flag_clear(USART0, USART_INT_FLAG_IDLE);
|
||
// 在这里添加空闲中断处理逻辑
|
||
}
|
||
}
|
||
|
||
void usart1_irq_handler(void) {
|
||
// 处理USART1的接收中断
|
||
if(usart_interrupt_flag_get(USART1, USART_INT_FLAG_RBNE)) {
|
||
uint8_t data = usart_data_receive(USART1);
|
||
// 使用原有的环形缓冲区处理逻辑
|
||
(void)uart_ring_buffer_put(data); // 缓冲满时丢弃，返回值可用于统计
|
||
}
|
||
|
||
// 处理USART1的空闲中断
|
||
if(usart_interrupt_flag_get(USART1, USART_INT_FLAG_IDLE)) {
|
||
usart_interrupt_flag_clear(USART1, USART_INT_FLAG_IDLE);
|
||
// 在这里添加空闲中断处理逻辑
|
||
}
|
||
}
|