diff --git a/inc/board_config.h b/inc/board_config.h
index 48fa1dd..5a8314c 100644
--- a/inc/board_config.h
+++ b/inc/board_config.h
@@ -5,6 +5,10 @@
 #ifndef BOARD_CONFIG_H
 #define BOARD_CONFIG_H
 
+#define SOFTWARE_IIC
+
+// #define DEBUG_VERBOES
+
 /******************************************************************************/
 
 #define I2C_SPEED       20000
@@ -18,4 +22,15 @@
 
 /******************************************************************************/
 
+#define RS485_RCU            RCU_USART0
+#define RS485_GPIO_RCU       RCU_GPIOA
+#define RS485_GPIO_PORT      GPIOA
+#define RS485_TX_PIN         GPIO_PIN_2
+#define RS485_RX_PIN         GPIO_PIN_3
+#define RS485_PHY            USART0
+#define RS485_BAUDRATE       115200U
+#define RS485_EN_PIN         GPIO_PIN_1
+
+/******************************************************************************/
+
 #endif //BOARD_CONFIG_H
diff --git a/inc/ldc1612.h b/inc/ldc1612.h
index 2e0ada9..f11cae6 100644
--- a/inc/ldc1612.h
+++ b/inc/ldc1612.h
@@ -13,8 +13,12 @@
 #include <stdio.h>
 #include <stdlib.h>
 #include <math.h>
+#include "board_config.h"
+#include "soft_i2c.h"
 #include "i2c.h"
 
+/***************************************************************************/
+
 #define LDC1612_ADDR         (0x2B << 1)
 
 /*Register Rddr*/
diff --git a/inc/soft_i2c.h b/inc/soft_i2c.h
index 58442ab..5b4d23e 100644
--- a/inc/soft_i2c.h
+++ b/inc/soft_i2c.h
@@ -22,6 +22,12 @@
 
 /******************************************************************************/
 
+#define SOFT_I2C_OK          1
+#define SOFT_I2C_FAIL        0
+#define SOFT_I2C_END         1
+
+/******************************************************************************/
+
 void soft_i2c_delay(void);
 
 void soft_i2c_config(void);
@@ -40,4 +46,8 @@ void soft_i2c_send_byte(uint8_t data);
 
 uint8_t soft_i2c_receive_byte(uint8_t ack);
 
+uint8_t soft_i2c_write_16bits(uint8_t slave_addr, uint8_t reg_addr, uint8_t data[2]);
+
+uint8_t soft_i2c_read_16bits(uint8_t slave_addr, uint8_t reg_addr, uint8_t *data);
+
 #endif //SOFT_I2C_H
diff --git a/inc/tmp112.h b/inc/tmp112.h
index 659a3d6..29b2436 100644
--- a/inc/tmp112.h
+++ b/inc/tmp112.h
@@ -13,7 +13,14 @@
 #include <stdio.h>
 #include <stdlib.h>
 #include <math.h>
+
+#include "board_config.h"
+
+#ifdef SOFTWARE_IIC
+#include "soft_i2c.h"
+#else
 #include "i2c.h"
+#endif
 
 /******************************************************************************/
 
diff --git a/src/i2c.c b/src/i2c.c
index 3c018dd..99aa01f 100644
--- a/src/i2c.c
+++ b/src/i2c.c
@@ -32,6 +32,8 @@ void i2c_gpio_config(void) {
     \retval     none
 */
 void i2c_config(void) {
+    /* configure I2C GPIO */
+    i2c_gpio_config();
     /* enable I2C clock */
     rcu_periph_clock_enable(RCU_I2C);
     /* configure I2C clock */
diff --git a/src/ldc1612.c b/src/ldc1612.c
index 5c104ad..8580255 100644
--- a/src/ldc1612.c
+++ b/src/ldc1612.c
@@ -12,7 +12,12 @@ void ldc1612_set_conversion_time(uint8_t channel, uint16_t result) {
     uint8_t data[2] = {0};
     data[0] = (result >> 8) & 0xFF;
     data[1] = result & 0xFF;
+
+#ifdef SOFTWARE_IIC
+    soft_i2c_write_16bits(LDC1612_ADDR, SET_CONVERSION_TIME_REG_START + channel, data);
+#else
     i2c_write_16bits(LDC1612_ADDR, SET_CONVERSION_TIME_REG_START + channel, data);
+#endif
 }
 
 /** @brief set conversion offset.
@@ -23,7 +28,12 @@ void ldc1612_set_conversion_offset(uint8_t channel, uint16_t result) {
     uint8_t data[2] = {0};
     data[0] = (result >> 8) & 0xFF;
     data[1] = result & 0xFF;
+#ifdef SOFTWARE_IIC
+    soft_i2c_write_16bits(LDC1612_ADDR, SET_CONVERSION_OFFSET_REG_START + channel, data);
+#else
     i2c_write_16bits(LDC1612_ADDR, SET_CONVERSION_OFFSET_REG_START + channel, data);
+#endif
+
 }
 
 /** @brief Before conversion,wait LC sensor stabilize for a short time.
@@ -34,7 +44,11 @@ void ldc1612_set_LC_stabilize_time(uint8_t channel, uint16_t result) {
     uint8_t data[2] = {0};
     data[0] = (result >> 8) & 0xFF;
     data[1] = result & 0xFF;
+#ifdef SOFTWARE_IIC
+    soft_i2c_write_16bits(LDC1612_ADDR, SET_LC_STABILIZE_REG_START + channel, data);
+#else
     i2c_write_16bits(LDC1612_ADDR, SET_LC_STABILIZE_REG_START + channel, data);
+#endif
 }
 
 /** @brief set input frequency divide and fref divide.
@@ -65,8 +79,11 @@ void ldc1612_set_freq_divide(uint8_t channel) {
     data[0] = (value >> 8) & 0xFF;
     data[1] = value & 0xFF;
     // printf("\tFIN_DIV: %d, FREF_DIV: %d\r\n", fin_div, freq_div);
-
+#ifdef SOFTWARE_IIC
+    soft_i2c_write_16bits(LDC1612_ADDR, SET_FREQ_REG_START + channel, data);
+#else
     i2c_write_16bits(LDC1612_ADDR, SET_FREQ_REG_START + channel, data);
+#endif
 }
 
 /** @brief Error output config.
@@ -77,7 +94,11 @@ void ldc1612_set_error_config(uint16_t value) {
     data[0] = (value >> 8) & 0xFF;
     data[1] = value & 0xFF;
 
+#ifdef SOFTWARE_IIC
+    soft_i2c_write_16bits(LDC1612_ADDR, ERROR_CONFIG_REG, data);
+#else
     i2c_write_16bits(LDC1612_ADDR, ERROR_CONFIG_REG, data);
+#endif
 }
 
 /** @brief mux  config.
@@ -88,7 +109,11 @@ void ldc1612_set_mux_config(uint16_t value) {
     data[0] = (value >> 8) & 0xFF;
     data[1] = value & 0xFF;
 
+    #ifdef SOFTWARE_IIC
+    soft_i2c_write_16bits(LDC1612_ADDR, MUL_CONFIG_REG, data);
+    #else
     i2c_write_16bits(LDC1612_ADDR, MUL_CONFIG_REG, data);
+    #endif
 }
 
 /** @brief reset sensor.
@@ -98,7 +123,12 @@ void ldc1612_reset_sensor(void) {
     uint8_t data[2] = {0};
     data[0] = 0x80;
     data[1] = 0x00;
+
+    #ifdef SOFTWARE_IIC
+    soft_i2c_write_16bits(LDC1612_ADDR, SENSOR_RESET_REG, data);
+    #else
     i2c_write_16bits(LDC1612_ADDR, SENSOR_RESET_REG, data);
+    #endif
 }
 
 /** @brief set drive current of sensor.
@@ -109,7 +139,11 @@ void ldc1612_set_drive_current(uint8_t channel, uint16_t value) {
     data[0] = (value >> 8) & 0xFF;
     data[1] = value & 0xFF;
 
+    #ifdef SOFTWARE_IIC
+    soft_i2c_write_16bits(LDC1612_ADDR, SET_DRIVER_CURRENT_REG + channel, data);
+    #else
     i2c_write_16bits(LDC1612_ADDR, SET_DRIVER_CURRENT_REG + channel, data);
+    #endif
 }
 
 /** @brief Main config part of sensor.Contains select channel、start conversion、sleep mode、sensor activation mode、INT pin disable ..
@@ -120,7 +154,11 @@ void ldc1612_set_sensor_config(uint16_t value) {
     data[0] = (value >> 8) & 0xFF;
     data[1] = value & 0xFF;
 
+    #ifdef SOFTWARE_IIC
+    soft_i2c_write_16bits(LDC1612_ADDR, SENSOR_CONFIG_REG, data);
+    #else
     i2c_write_16bits(LDC1612_ADDR, SENSOR_CONFIG_REG, data);
+    #endif
 }
 
 void ldc1612_single_ch0_config(void) {
@@ -141,23 +179,41 @@ void ldc1612_single_ch0_config(void) {
 
 void ldc1612_iic_get_sensor_infomation(void) {
     uint8_t data[2] = {0};
-    // ldc1612_iic_read_16bits(READ_MANUFACTURER_ID, data);
+
+#ifdef SOFTWARE_IIC
+    soft_i2c_read_16bits(LDC1612_ADDR, READ_MANUFACTURER_ID, data);
+#else
     i2c_read_16bits(LDC1612_ADDR, READ_MANUFACTURER_ID, data);
+#endif
     printf("\tManufacturer: 0x%x", (data[0] << 8) | data[1]);
-    // ldc1612_iic_read_16bits(READ_DEVICE_ID, data);
+
+#ifdef SOFTWARE_IIC
+    soft_i2c_read_16bits(LDC1612_ADDR, READ_DEVICE_ID, data);
+#else
     i2c_read_16bits(LDC1612_ADDR, READ_DEVICE_ID, data);
+#endif
     printf("\tDevice: 0x%x", (data[0] << 8) | data[1]);
 }
 
 uint16_t ldc1612_get_manufacturer_id(void) {
     uint8_t data[2] = {0};
+
+#ifdef SOFTWARE_IIC
+    soft_i2c_read_16bits(LDC1612_ADDR, READ_MANUFACTURER_ID, data);
+#else
     i2c_read_16bits(LDC1612_ADDR, READ_MANUFACTURER_ID, data);
+#endif
     return (data[0] << 8) | data[1];
 }
 
 uint16_t ldc1612_get_deveice_id(void) {
     uint8_t data[2] = {0};
+
+#ifdef SOFTWARE_IIC
+    soft_i2c_read_16bits(LDC1612_ADDR, READ_DEVICE_ID, data);
+#else
     i2c_read_16bits(LDC1612_ADDR, READ_DEVICE_ID, data);
+#endif
     return (data[0] << 8) | data[1];
 }
 
@@ -169,11 +225,18 @@ uint32_t ldc1612_get_raw_channel_result(uint8_t channel) {
     uint32_t raw_value = 0;
     uint8_t value[2] = {0};
 
-    // ldc1612_iic_read_16bits(CONVERTION_RESULT_REG_START + channel, value);
+#ifdef SOFTWARE_IIC
+    soft_i2c_read_16bits(LDC1612_ADDR, CONVERTION_RESULT_REG_START + channel, value);
+#else
     i2c_read_16bits(LDC1612_ADDR, CONVERTION_RESULT_REG_START + channel, value);
+#endif
     raw_value |= (uint32_t) ((value[0] << 8) | value[1]) << 16;
-    // ldc1612_iic_read_16bits(CONVERTION_RESULT_REG_START + channel + 1, value);
+
+#ifdef SOFTWARE_IIC
+    soft_i2c_read_16bits(LDC1612_ADDR, CONVERTION_RESULT_REG_START + channel + 1, value);
+#else
     i2c_read_16bits(LDC1612_ADDR, CONVERTION_RESULT_REG_START + channel + 1, value);
+#endif
     raw_value |= (uint32_t) ((value[0] << 8) | value[1]);
     return ldc1612_parse_raw_result(raw_value);
 }
diff --git a/src/main.c b/src/main.c
index 939e614..092d290 100644
--- a/src/main.c
+++ b/src/main.c
@@ -12,12 +12,14 @@
 #include "rs485.h"
 #include "led.h"
 #include "i2c.h"
-#include "soft_i2c.h"
 #include "ldc1612.h"
-#include "tmp112.h"
+#include "board_config.h"
 
-uint32_t g_temperature_uint32;
-uint32_t g_eddy_current_value_uint32;
+#ifdef SOFTWARE_IIC
+#include "soft_i2c.h"
+#else
+#include "i2c.h"
+#endif
 
 void watchdog_init(void) {
     /* Enable the LSI clock */
@@ -59,73 +61,16 @@ int main(void) {
 
     // watchdog_init();
     /* configure I2C */
-    // i2c_gpio_config();
-    // i2c_config();
+    soft_i2c_config();
 
-    // ldc1612_iic_get_sensor_infomation();
+    ldc1612_iic_get_sensor_infomation();
     /* configure LDC1612 */
-    // ldc1612_single_ch0_config();
-
-    uint8_t data[2] = {0};
-
-    printf("Start\n");
-
-
+    ldc1612_single_ch0_config();
 
     /* Initialize watchdog */
     watchdog_init();
 
     while (1) {
-        soft_i2c_config();
-        printf("111\n");
-
-        soft_i2c_start();
-        soft_i2c_send_byte((0x2B << 1));
-        if (!soft_i2c_wait_ack())
-        {
-            printf("NACK\n");
-        }
-
-
-        soft_i2c_send_byte(0x7E);
-        if (!soft_i2c_wait_ack())
-        {
-            printf("NACK\n");
-        }
-
-        soft_i2c_delay();
-        soft_i2c_start();
-
-        soft_i2c_send_byte((0x2B << 1) + 1);
-        if (!soft_i2c_wait_ack())
-        {
-            printf("NACK\n");
-        }
-
-        soft_i2c_delay();
-
-        data[0] = soft_i2c_receive_byte(1);
-        data[1] = soft_i2c_receive_byte(0);
-
-        delay_us(5);
-        soft_i2c_stop();
-
-        printf("0x%x 0x%x\n", data[0], data[1]);
-
-
-
-
-
-        // i2c_start();
-        // delay_ms(1);
-        // i2c_stop();
-        // delay_ms(1);
-        delay_ms(1000);
-        // g_eddy_current_value_uint32 = 0;
-        // g_temperature_uint32 = 0;
-        // g_eddy_current_value_uint32 = ldc1612_get_raw_channel_result(CHANNEL_0);
-        // g_temperature_uint32 = tmp112a_get_raw_channel_result();
-        printf("1\n");
         delay_ms(99);
         fwdgt_counter_reload();
     }
diff --git a/src/rs485.c b/src/rs485.c
index dbce5c4..c471eca 100644
--- a/src/rs485.c
+++ b/src/rs485.c
@@ -4,9 +4,6 @@
 
 #include "rs485.h"
 
-extern uint32_t g_temperature_uint32;
-extern uint32_t g_eddy_current_value_uint32;
-
 uint8_t package_header[3] = {0xB5, 0xF0, 0x04};
 uint8_t package_data[4] = {0};
 
diff --git a/src/soft_i2c.c b/src/soft_i2c.c
index 837c1f1..a985aef 100644
--- a/src/soft_i2c.c
+++ b/src/soft_i2c.c
@@ -47,11 +47,11 @@ void soft_i2c_start(void) {
     // sda_out();
     I2C_SDA_HIGH();
     I2C_SCL_HIGH();
-    i2c_delay();
+    soft_i2c_delay();
     I2C_SDA_LOW();
-    i2c_delay();
+    soft_i2c_delay();
     I2C_SCL_LOW();
-    // i2c_delay();
+    // soft_i2c_delay();
     // 从全高开始，SCL为高期间，SDA下降沿表示start信号，再拉低SCL
 }
 
@@ -65,9 +65,9 @@ void soft_i2c_stop(void) {
     // sda_out();
     I2C_SCL_LOW();
     I2C_SDA_LOW();
-    i2c_delay();
+    soft_i2c_delay();
     I2C_SCL_HIGH();
-    i2c_delay();
+    soft_i2c_delay();
     I2C_SDA_HIGH();
     // 从全低开始，SCL为高期间，SDA上升沿表示stop
 }
@@ -81,11 +81,11 @@ void soft_i2c_stop(void) {
 void soft_i2c_send_ack(void) {
     // sda_out();
     I2C_SDA_LOW();
-    i2c_delay();
+    soft_i2c_delay();
     I2C_SCL_HIGH();
-    i2c_delay();
+    soft_i2c_delay();
     I2C_SCL_LOW();
-    i2c_delay();
+    soft_i2c_delay();
     I2C_SDA_HIGH();
     // SCL产生一个正常的时钟周期，其间SDA始终为低电平，表示ACK
 }
@@ -99,11 +99,11 @@ void soft_i2c_send_ack(void) {
 void soft_i2c_send_nack(void) {
     // sda_out();
     I2C_SDA_HIGH();
-    i2c_delay();
+    soft_i2c_delay();
     I2C_SCL_HIGH();
-    i2c_delay();
+    soft_i2c_delay();
     I2C_SCL_LOW();
-    i2c_delay();
+    soft_i2c_delay();
     I2C_SDA_HIGH();
     // SCL产生一个正常的时钟周期，其间SDA始终为高电平，表示NACK
 }
@@ -117,9 +117,9 @@ void soft_i2c_send_nack(void) {
 uint8_t soft_i2c_wait_ack(void) {
     // sda_in();
     I2C_SDA_HIGH();
-    i2c_delay();
+    soft_i2c_delay();
     I2C_SCL_HIGH();
-    i2c_delay();
+    soft_i2c_delay();
     uint8_t ack = !I2C_SDA_READ();
     //ACK信号是第九个时钟期间，SDA被从机在SCL高期间，拉低并保持低电平。此处判断SDA是否被拉低，被拉低则返回0，取反为1，表示收到ACK
     I2C_SCL_LOW();
@@ -141,9 +141,9 @@ void soft_i2c_send_byte(uint8_t byte) {
             I2C_SDA_LOW(); //SCL低电平期间，SDA低电平表示0
         }
         byte <<= 1; //左移一位，把原本第二位的数据移到第一位，再判断高低电平
-        i2c_delay();
+        soft_i2c_delay();
         I2C_SCL_HIGH(); //SCL拉高电平，SDA电平状态保持不变
-        i2c_delay();
+        soft_i2c_delay();
         I2C_SCL_LOW(); //SCL拉低电平
         delay_us(5);
     }
@@ -163,12 +163,12 @@ uint8_t soft_i2c_receive_byte(uint8_t ack) {
     for (int i = 0; i < 8; i++) {
         byte <<= 1;
         I2C_SCL_HIGH();
-        i2c_delay();
+        soft_i2c_delay();
         if (I2C_SDA_READ()) {
             byte |= 0x01;
         }
         I2C_SCL_LOW();
-        i2c_delay();
+        soft_i2c_delay();
     }
     if (ack) {
         soft_i2c_send_ack();
@@ -176,4 +176,53 @@ uint8_t soft_i2c_receive_byte(uint8_t ack) {
         soft_i2c_send_nack();
     }
     return byte;
+}
+
+uint8_t soft_i2c_write_16bits(uint8_t slave_addr, uint8_t reg_addr, uint8_t data[2]) {
+    soft_i2c_start();
+    soft_i2c_send_byte(slave_addr);
+    if (!soft_i2c_wait_ack()) {
+        soft_i2c_stop();
+        return SOFT_I2C_FAIL;
+    }
+    soft_i2c_send_byte(reg_addr);
+    if (!soft_i2c_wait_ack()) {
+        soft_i2c_stop();
+        return SOFT_I2C_FAIL;
+    }
+    soft_i2c_send_byte(data[0]);
+    if (!soft_i2c_wait_ack()) {
+        soft_i2c_stop();
+        return SOFT_I2C_FAIL;
+    }
+    soft_i2c_send_byte(data[1]);
+    if (soft_i2c_wait_ack()){}
+    soft_i2c_stop();
+    return SOFT_I2C_OK;
+}
+
+uint8_t soft_i2c_read_16bits(uint8_t slave_addr, uint8_t reg_addr, uint8_t *data)
+{
+    soft_i2c_start();
+    soft_i2c_send_byte(slave_addr);
+    if (!soft_i2c_wait_ack()) {
+        soft_i2c_stop();
+        return SOFT_I2C_FAIL;
+    }
+    soft_i2c_send_byte(reg_addr);
+    if (!soft_i2c_wait_ack()) {
+        soft_i2c_stop();
+        return SOFT_I2C_FAIL;
+    }
+    soft_i2c_start();
+    soft_i2c_send_byte(slave_addr | 0x01);
+    if (!soft_i2c_wait_ack()) {
+        soft_i2c_stop();
+        return SOFT_I2C_FAIL;
+    }
+    soft_i2c_delay();
+    data[0] = soft_i2c_receive_byte(1);
+    data[1] = soft_i2c_receive_byte(0);
+    soft_i2c_stop();
+    return SOFT_I2C_OK;
 }
\ No newline at end of file
diff --git a/src/tmp112.c b/src/tmp112.c
index 713bc46..d28ce94 100644
--- a/src/tmp112.c
+++ b/src/tmp112.c
@@ -9,7 +9,13 @@ uint32_t tmp112a_get_raw_channel_result(void) {
     uint8_t value[2] = {0};
 
     // ldc1612_iic_read_16bits(CONVERTION_RESULT_REG_START + channel, value);
+
+#ifdef SOFTWARE_IIC
+    soft_i2c_read_16bits(TMP112A_ADDR, 0x00, value);
+#else
     i2c_read_16bits(TMP112A_ADDR, 0x00, value);
+#endif
+
     raw_value = ((uint16_t) (value[0] << 4) | (value[1]>>4));
     return (raw_value * 625);
 }