#include "uart.h"
#include "gd32e23x_usart.h"
#include "gd32e23x_rcu.h"
#include "gd32e23x_gpio.h"
#include "board_config.h"


void rs485_init(void) {

    #ifndef RS485_MAX13487
    /* 使能 GPIOA 和 USART0 时钟 */
    rcu_periph_clock_enable(RS485_GPIO_RCU);
    rcu_periph_clock_enable(RS485_RCU);

    /* 配置 PA2 为 USART0_TX，PA3 为 USART0_RX */
    gpio_af_set(RS485_GPIO_PORT, GPIO_AF_1, RS485_TX_PIN | RS485_RX_PIN | RS485_EN_PIN);

    gpio_mode_set(RS485_GPIO_PORT, GPIO_MODE_AF, GPIO_PUPD_PULLUP, RS485_TX_PIN | RS485_RX_PIN);
    gpio_output_options_set(RS485_GPIO_PORT, GPIO_OTYPE_PP, GPIO_OSPEED_50MHZ, RS485_TX_PIN | RS485_RX_PIN);

    gpio_mode_set(RS485_GPIO_PORT, GPIO_MODE_AF, GPIO_PUPD_NONE, RS485_EN_PIN);
    gpio_output_options_set(RS485_GPIO_PORT, GPIO_OTYPE_PP, GPIO_OSPEED_50MHZ, RS485_EN_PIN);

    /* 配置波特率、数据位、停止位等 */
    usart_deinit(RS485_PHY);
    usart_word_length_set(RS485_PHY, USART_WL_8BIT);
    usart_stop_bit_set(RS485_PHY, USART_STB_1BIT);
    usart_parity_config(RS485_PHY, USART_PM_NONE);
    usart_baudrate_set(RS485_PHY, RS485_BAUDRATE);
    usart_receive_config(RS485_PHY, USART_RECEIVE_ENABLE);
    usart_transmit_config(RS485_PHY, USART_TRANSMIT_ENABLE);

    usart_driver_assertime_config(RS485_PHY, 0x01);
    usart_driver_deassertime_config(RS485_PHY, 0x10);

    usart_rs485_driver_enable(RS485_PHY);

    usart_enable(RS485_PHY);

    nvic_irq_enable(USART0_IRQn, 0);
    usart_interrupt_enable(RS485_PHY, USART_INT_RBNE);
    // usart_interrupt_enable(RS485_PHY, USART_INT_IDLE);

    #else
    rcu_periph_clock_enable(RS485_GPIO_RCU);
    rcu_periph_clock_enable(RS485_RCU);

    gpio_af_set(RS485_GPIO_PORT, GPIO_AF_1, GPIO_PIN_2 | GPIO_PIN_3);

    /* configure USART Tx&Rx as alternate function push-pull */
    gpio_mode_set(RS485_GPIO_PORT, GPIO_MODE_AF, GPIO_PUPD_PULLUP, RS485_TX_PIN | RS485_RX_PIN);
    gpio_output_options_set(RS485_GPIO_PORT, GPIO_OTYPE_PP, GPIO_OSPEED_10MHZ, RS485_TX_PIN | RS485_RX_PIN);

    /* configure RS485 EN Pin */
    gpio_mode_set(RS485_GPIO_PORT, GPIO_MODE_OUTPUT, GPIO_PUPD_NONE, RS485_EN_PIN);
    gpio_output_options_set(RS485_GPIO_PORT, GPIO_OTYPE_PP, GPIO_OSPEED_50MHZ, RS485_EN_PIN);
    gpio_bit_write(RS485_GPIO_PORT, RS485_EN_PIN, SET);

    /* USART configure */
    usart_deinit(RS485_PHY);
    usart_baudrate_set(RS485_PHY, RS485_BAUDRATE);
    usart_receive_config(RS485_PHY, USART_RECEIVE_ENABLE);
    usart_transmit_config(RS485_PHY, USART_TRANSMIT_ENABLE);

    usart_enable(RS485_PHY);

    nvic_irq_enable(USART0_IRQn, 0);
    usart_interrupt_enable(RS485_PHY, USART_INT_RBNE);
    usart_interrupt_enable(RS485_PHY, USART_INT_IDLE);

    #endif // RS485_MAX13487
    }

// static uart_printf_port_t g_printf_port = UART_PRINTF_USART0;

// void uart_set_printf_port(uart_printf_port_t port) {
//     g_printf_port = port;
// }

// // printf 重定向，支持多串口
// int __io_putchar(int ch) {
//     switch (g_printf_port) {
//         case UART_PRINTF_USART0:
//             while (usart_flag_get(USART0, USART_FLAG_TBE) == RESET) {}
//             usart_data_transmit(USART0, (uint8_t)ch);
//             break;
//         case UART_PRINTF_USART1:
//             while (usart_flag_get(USART1, USART_FLAG_TBE) == RESET) {}
//             usart_data_transmit(USART1, (uint8_t)ch);
//             break;
//         case UART_PRINTF_BOTH:
//             while (usart_flag_get(USART0, USART_FLAG_TBE) == RESET) {}
//             usart_data_transmit(USART0, (uint8_t)ch);
//             while (usart_flag_get(USART1, USART_FLAG_TBE) == RESET) {}
//             usart_data_transmit(USART1, (uint8_t)ch);
//             break;
//         default:
//             break;
//     }
//     return ch;
// }